“Perpetual Pavement” is a term used to describe a long-lasting structural design, construction and maintenance concept for HMA pavements. If properly maintained and rehabilitated, a perpetual pavement can be designed and built to last longer than 50 years without requiring major structural rehabilitation or reconstruction, and needing only periodic surface renewal in response to distresses confined to the top of the pavement.
The concept of perpetual pavements, or long-lasting HMA pavements, is not new. Full-depth and deep-strength HMA pavement structures have been constructed since the 1960s and before, and those that were well-designed and well-built have been very successful in providing long service lives under heavy traffic (APA, 2001). Advancements in milling, recycling and HMA technology over the last few decades have created HMA pavements that perform better, longer and with lower life-cycle costs than was previously possible.
As Michael Nunn pointed out in 1998, flexible pavements over a minimum strength are not likely to exhibit structural damage even when subjected to very high traffic flows over long periods of time. He noted that existing pavements over about 370 mm (14.5 inches) should be able to withstand an almost infinite number of axle loads without structural deterioration due to either fatigue cracking or rutting of the subgrade. Deterioration in these thick, strong pavements was observed to initiate in the pavement surface as either top-down cracking or rutting. Further, Uhlmeyer et al. (2000) found that most HMA pavements thicker than about 160 mm (6.3 inches) exhibit only surface-initiated top-down cracking. Therefore, if surface-initiated cracking and rutting can be accounted for before they impact the structural integrity of the pavement, the pavement life could be greatly increased.
Researchers have used this idea as well as pavement materials research to develop a basic perpetual pavement structural concept. This concept uses a thick asphalt over a strong foundation design with three HMA layers, each one tailored to resist specific stresses (TRB, 2001):
- HMA base layer. This is the bottom layer designed specifically to resist fatigue cracking. Two approaches can be used to resist fatigue cracking in the base layer. First, the total pavement thickness can be made great enough such that the tensile strain at the bottom of the base layer is insignificant. Alternatively, the HMA base layer could be made using an extra-flexible HMA. This can be most easily accomplished by increasing the asphalt content. Combinations of the previous two approaches also work.
- Intermediate layer. This is the middle layer designed specifically to carry most of the traffic load. Therefore it must be stable (able to resist rutting) as well as durable. Stability can best be provided by using stone-on-stone contact in the coarse aggregate and using a binder with the appropriate high-temperature grading.
- Wearing surface. This is the top layer designed specifically to resist surface-initiated distresses such as top-down cracking and rutting. Other specific distresses of concern would depend upon local experience.
In order to work, the above pavement structure must be built on a solid foundation. Nunn (1998) notes that rutting on roads built on subgrade with a CBR greater than 5 percent originates almost solely in the HMA layers, which suggests that a subgrade with a CBR greater than 5 percent (resilient modulus greater than about 7,000 psi (50 MPa)) should be considered adequate. As always, proper construction techniques are essential to a perpetual pavement’s performance. Figure 1 shows an example cross-section of a perpetual pavement design to be used in California on I-710 (the Long Beach Freeway) in Los Angeles County.
- Asphalt Pavement Alliance (APA). (2001b). New Award Program Honors Long-Lasting Hot Mix Asphalt Pavements. 9 August 2001 press release.↵
- Design of Long-Life Roads for Heavy Traffic. Australian Asphalt Pavement Association Industry Conference. Surfers Paradise, Queensland, Australia.↵
- Top-Down Cracking in Washington State Asphalt Concrete Wearing Courses. Transportation Research Record 1730. Transportation Research Board, National Research Council, Washington, D.C. pp. 110-116.↵
- Study for a Future Strategic Highway Research Program Project Description. National Academy of Sciences. Washington D.C. Accessed 1 October 2003.↵
- Asphalt Pavement Alliance (APA). (no date given). Perpetual Pavement on I-40 in Oklahoma City. Asphalt Pavement Alliance web site .pdf document. http://www.asphaltalliance.com. Accessed 15 October 2001.↵