Construction
Construction_250

PCC Truck Mixer

Print this pageEmail this to someoneShare on FacebookTweet about this on TwitterShare on Google+Share on LinkedInShare on RedditDigg this

Truck mixers are the most common mode of PCC transport. They consist of a truck-mounted drum that rotates on an inclined axis. A typical mixing truck (Figures 1 and 2) uses a 6.9 – 9.2 m3 (9 – 12 yd3) mixing drum, the size being limited due to gross vehicle weight of the loaded truck. When used to transport truck mixed PCC, drums can be filled to a maximum of 63 percent of their total volume. When used to transport central mixed PCC, drums can be filled to a maximum of 80 percent of their total volume (AASHTO, 2000[1]). Generally, ready mixed concrete producers, load their trucks with a quantity at or near the rated mixer capacity (NRMCA, 2002[2]). Mixing drums contain helical blades on their inside walls that are designed to push PCC to the bottom of the drum when rotated in the “mixing” direction and out to the discharge point when rotated in the opposite, or “discharge” direction. Most truck mixers discharge to the rear, however, front discharging truck mixers are gaining in popularity because the driver can drive directly onto a site and mechanically control the positioning of the discharge chute without the help of contractor personnel (NRMCA, 2002[2]). Discharge is typically via a 3 – 6 m (10 – 20 ft.) chute. Truck mixers use revolution counters to keep track of total drum revolutions and may also be equipped with slump meters (usually accurate to about 12.5 mm (0.5 inches)) and digital water meters to monitor water usage (ACPA, 1995[3]).

Figure 1. Typical truck mixer.

Figure 2. Large truck mixer.

Agitation

Drum rotation (Video 1) is used for two purposes: mixing and agitation. High speed rotation (on the order of 12 – 15 rpm) is used to mix PCC ingredients into a homogenous material. This type of mixing typically takes between 50 and 100 revolutions depending upon PCC characteristics and environmental factors. After this period of mixing, the PCC is usually required to meet at least 5 of the 6 homogeneity specifications listed in Table 1. Samples for these specifications should be taken from widely separated portions but should also come from the middle 15 – 85 percent of the load so as not to be influenced by beginning and end of load abnormalities.

 

Table 1. Ready-Mix Concrete Homogeneity Test Requirements from AASHTO M 157 and ASTM C 94
Parameter  Maximum Permissible Difference in Results of Tests Taken from Two Locations in the PCC Batch
Metric English
Weight per unit volume calculated to an air-free basis 16 kg/m3 1 lb/ft3
Air content 1.0 % 1.0 %
Slump
If average slump < 102 mm (4 inches)
If average slump is 102 – 152 mm (4 – 6 inches)
25 mm
1.0 inch
38 mm
1.5 inches
Coarse aggregate content
(percent by weight retained on the 4.75 mm (No. 4) sieve)
6.0 % 6.0 %
Unit weight of air-free mortar
(based on an average of all comparative samples tested)
1.6 % 1.6 %
Average 7-day compressive strength for each sample (based on an average of all comparative test specimens) 7.5 % 7.5 %

 

Low speed rotation (about 2 rpm) is used to agitate the PCC to (1) maintain its homogeneity and (2) prevent slump loss while in transit. Truck mixers are equipped with a revolution counter to help maintain tight control over the total number of drum revolutions. Mixing, which is generally short in duration, is usually planned for a specific time or place. If not mixing, truck mixers usually operate in the low speed agitation mode. Mixing is typically done using one of the following three methods (NRMCA, 2002[2]):

  • Mixing at the batching facility. The drum is turned at high speed (12 – 15 rpm) for about 50 revolutions while at the production facility, which allows for a quick check of batch characteristics. The PCC is then agitated (< 2 rpm) while in transit to the paving site.
  • Mixing in transit. The drum is turned at medium speed (about 8 rpm) for 70 revolutions while driving to the job site. The PCC is agitated (< 2 rpm) until discharge.
  • Mixing at the paving site. The PCC is agitated (< 2 rpm) while in transit to the paving site. Upon arrival, the PCC is mixed (12 – 15 rpm) for 70 to 100 revolutions, or about five minutes.

 

Video 1. Concrete mixing truck drum rotation speeds.

In general, short times between mixing and placement can better avoid the problems of premature hardening and slump loss that result from potential delays in transit. Regardless of the mixing mode, PCC is a perishable construction material. First, if it begins to set before being placed and consolidated it is of little use. Second, if it is mixed and agitated excessively it can loose its air entrainment or the effects of certain admixtures can diminish. Therefore, a typical specification will require that ready mixed PCC delivered to the paving site meet the following criteria:

  • A minimum time (often 1 to 2 hours) between the time at which when the mixing water was introduced to the portland cement and aggregates and discharge at the site.
  • A maximum number of revolutions (typically around 300) between the time at which when the mixing water was introduced to the portland cement and aggregates and discharge at the site.



Footnotes    (↵ returns to text)
  1. American Association of State Highway and Transportation Officials (AASHTO).  (2000).  Standard Specifications for Transportation Materials and Methods of Sampling and Testing, Twentieth Edition.  American Association of State Highway and Transportation Officials.  Washington, D.C.
  2. National Ready Mixed Concrete Association (NRMCA).  (no date given).  NRMCA web site, Concrete Basics home page.  National Ready Mixed Concrete Association.  Silver Spring, MD.  http://www.nrmca.org.  Accessed 11 February 2002.
  3. American Concrete Pavement Association (ACPA).  (1995).  Construction of Portland Cement Concrete Pavements.  National Highway Institute Course No. 13133.  AASHTO/FHWA/Industry joint training.  Federal Highway Administration, Department of Transportation.  Washington, D.C.

 

 

 

close citation

Thanks for sharing PCC Truck Mixer.